ACME Xperior 5R BEAM F Podręcznik Użytkownika

XperiorTM 5R BEAM F User Guide Please read these instructions carefully before use

XP-5R Beam F 9--○3 Button MENU To enter into, move backward or leave the menu UP Move up in the menu DOWN Move down in the menu ENTER Ent

10-5.2 Lamp Philips MSD Platinum 5R (8000K) y Because of its high internal pressure, there might be a risk that the Discharge lamp would explode d

XP-5R Beam F 11-- 2. Follow the Fig.3 and Fig.4: Loosen the two screws and apart the entire assembly 3. Follow the Fig.5 and Fig.6: Unplu

12- Fig.4 Fig.5 Explanation of fig.5: Base 40°C Show temperature of base CPU is 40°C 001 Show start address Md.1 15C

XP-5R Beam F 13--

14- DMX Functions Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Address, DMX Channel Mo

XP-5R Beam F 15--to exit menu mode. View DMX Value Select View DMX Value, press ENTER button to confirm. Channel function and its value will show on

16-Change or BL.O. Gobo Change. Pan Inverse Select Pan Inverse, press ENTER button to confirm, present mode will blink on the display, use UP and DOW

XP-5R Beam F 17--BL.O. Gobo Change—Blackout while change gobo Select BL.O. Gobo Change, press ENTER button to confirm, present mode will blink on the

18-“yes” mode). On If DMX On— Lamp turns on when DMX signal is detected Select On If DMX On, press ENTER button to confirm, present mode will blink

XP-5R Beam F 1-- TABLE OF CONTENTS 1. Safety Instruction... 2 2. Install

XP-5R Beam F 19--or Temperature unit. Display Inverse Select Display Inverse, press ENTER button to confirm, present mode will blink on the display,

20-automatically test pan, tilt, color, gobo, gobo rotation, shutter, dimmer, prism, prism rotation, frost, focus, and lamp on/off. . Press MENU butt

XP-5R Beam F 21--Reset Functions Enter menu mode, select Reset Function, press ENTER button to confirm, use UP and DOWN button to select Pan/Tilt, Sh

22-Special Functions Enter menu mode, select Special Functions, press ENTER button to confirm, use UP and DOWN button to select Fixture Maintenance o

XP-5R Beam F 23-- Pan—pan home position adjust Enter offset mode, Select Pan, press ENTER button to confirm, the present position will blink on the d

24-Gobo—Gobo home position adjust Enter offset mode, Select Gobo, press ENTER button to confirm, the present position will blink on the display, us

XP-5R Beam F 25--6.4. Error Information Lamp Startup Fail It appears when there is no lamp or some wires are damaged. Temperature Sense Error It ap

26- 7. Control By Universal DMX Controller 7.1 Connection unit 1 unit 2 unit3 unit4 1. At last un

XP-5R Beam F 27--5. The end of the DMX 512 system should be terminated to reduce signal errors. 6. 3 pin XLR connectors are more popular than 5 pins

28-7.4 DMX 512 Configuration Please refer to below configurations to control the fixtures Attention: 1. The unit will maintain the last condition

2-1. Safety Instruction WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also

XP-5R Beam F 29--15 Channels mode1：

30-

XP-5R Beam F 31--14 Channels mode 2:

32-

XP-5R Beam F 33--18 Channels mode 3:

34-

XP-5R Beam F 35-- 7.5 Lighting Library Download The whole series of Xperior fixtures’ personalities have been built into the most widely used cons

36-9. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A.

XP-5R Beam F 37--E. If The pan belt is broken 1. Turn off the mains power. 2. Loosen the screws (A)，open the cover (B). 3. Loosen the screws (C).

38-10. Maintenance and Cleaning Maintenance: Ballast A. As the pictures shown above, pl

XP-5R Beam F 3--during its operation, and allow about 15 minutes for cooling the unit down before replacing bulb or maintenance as it could be very h

39393610525212112112222222222222236 Innovation, Quality, Performance

4-2. Installation Unpacking the fixture (for flight case pack only) 1. Stop the flight case via the brake sheet above the wheels. 2. Unlock the loc

XP-5R Beam F 5--y Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. y Make absolute su

6-Dimmer/Shutter - Mechanical dimmer - Mechanical shutter and adjustable speed strobe effect Color wheel - Color wheel: 14 fixed colors - Rainbow e

XP-5R Beam F 7--DMX Channels Mode CH Mode 1 15-CH Mode 2 14-CH Mode 3 18-CH 1 PAN COLOUR WHEEL COLOUR WHEEL 2 PAN FINE STOP / STROBE STOP

8-4. Description 4.1 Description of the fixture Caution: The head and arm must be unlocked before operation! 4.2 Control Pane